How To Set Up Kirby Carpet Shampooer
Disclaimer:
Goodvac.com is non affiliated with The Kirby Company and/or The Scott Fetzer Visitor. All manuals and maintenance tips for Kirby vacuum cleaners and repair manuals for Kirby model vacuums are authored past GoodVac.com and are not endorsed or canonical by the Kirby vacuum manufacturer - Kirby Company and/or The Scott Fetzer Visitor. These materials should be only used at your own discretion and hazard. .
Read our "Terms of Use".
| | |||||||
 | 1. Earlier shampooing rugs with whatever shampoo system you want to vacuum as good as possible. Spend two or 3 times more than time vacuuming the area as you normally would. | ||||||
 | ii.
If you don't you can find them in out Kirby Shampooer Parts department or you can buy entire Kirby Shampooer. | ||||||
 | 3. Brush ends are different so it is impossible to put information technology in incorrect. | ||||||
 | 4. Slide the nozzle over the tray and brush assembly. | ||||||
 | 5. Turn the knob to friction match reddish arrows. | ||||||
 | six. When turning the knob claw within the Kirby shampoo nozzle catches the belt, stretches information technology and now it is set up to exist installed on the Kirby vacuum. | ||||||
 | 7. To install the nozzle with tray you must have the Kirby front all the way upward. Simply printing on the pedal as far as it tin can become. Put the nozzle on, lock it onto the unit of measurement with the latch and twist the knob back (clockwise) to lucifer light-green arrows. Essentially this is the same as installing a regular nozzle so if it is still not quite clear - see NOZZLE INSTALATION INSTRUCTIONS. | ||||||
 | 8. Make sure Kirby shampoo tank has sponge (on the left) and suds screen (on the right). Sponge will prevent dust from Kirby frazzle clogging Kirby shampooer and the screen is necessary to brand the foam. If Kirby shampooer has no screen - wait in the shampooer hose as sometimes it stays in that location when taking shampooer apart. If suds screen keeps falling out of the tank - utilise plumbers tape or use lighter to rut upwards a bit the plastic cervix where the screen is inserted and push plastic a little flake in. Exist careful - exercise non gear up plastic on burn and exercise not burn your fingers. Practice it where it is safe so you do non ready you house on burn. NEVER glue the screen in - you may have to remove it to make clean. | ||||||
 | 9. Kirby shampooer tank has three marks. This indicates how many capfuls of Kirby shampoo yous have to add in the tank (shampooer tank cap acts as measuring loving cup). If y'all have water upwardly to the outset line - 1 cap total, if up to 2d line-ii. If up to the tertiary line - you guessed information technology - iii capfuls. Use warm or cool water. Never use hot water as it may damage the tank. | ||||||
| |||||||
 | 10. This ratio is if you are using regular (non concentrated) Kirby shampoo. | ||||||
 | 11. Install the tank with soapy solution in place of the bag, Nozzle with tray goes on the front of the unit just like the nozzle would. | ||||||
 | 12. Connect Kirby solution tank and tray with the hose. | ||||||
 | thirteen. Lower the tray all the way down every bit far as it can get. | ||||||
 | 14. For very dirty carpeting use shampoo pretreatment (Heavy Traffic) . Follow instructions on the canteen . | ||||||
 | 15. Turn on the Kirby, gear up tech drive in Drive (pedal on the back of the unit of measurement Kirby G3 and later) and start opening the valve. Soapy solution is being sprayed onto the screen that nosotros talked about and information technology generates the cream. Valve does not necessarily accept to be open all the fashion. It should generate just enough cream to evenly comprehend the carpet (run across 2d picture below). | ||||||
 | xvi. Foam has to be white and calorie-free. If you accept but soapy water coming out instead - check the suds screen. | ||||||
 | 17. Lay the foam by slowly pulling Kirby towards yourself. Before foam gets picked upwards it has to stay on the rug for about three minutes. Shampoo in sections about 4 ten 10 anxiety. Foam allows you to spread modest amount of h2o over the large area. And so soapy solution loosens the dirt from carpet fibers and it is ready to be collected. | ||||||
 | eighteen. When finished laying foam turn off the Kirby foam maker past turning the Kirby shampooer's tank knob to OFF position. | ||||||
 | 19. Start picking up the foam where you started laying it as information technology would be sitting on the rug for about 3 minutes now. Pull Kirby slowly in REVERSE over the foam. | ||||||
 | twenty. Since Kirby shampooer does not inject a lot of h2o in the carpet just simply moistens the fibers - there is not much h2o to pick up. There is no suction involved at all. Kirby Shampooer brush curlicue scrubs and rubs the fibers, scoops dirty water off and throws it into the shampooer tray on the front of the Kirby unit. Ordinarily you should expect to pick upwardly about xxx% of the water. The tray will starting time filling up with the dirty water so do not make sudden moves with the Kirby every bit you lot may end upward dumping it all back in one spot and stain is almost guaranteed. You may have empty the tray. | ||||||
 | 21. If in that location are some stains left you may desire to use some Kirby spot remover. Spray it on the spots. | ||||||
 | 22. Rub it in with a sponge (I prefer a castor) . | ||||||
 | 23. Shampoo the treated spot again. Very dirty areas you may desire to shampoo several times from several directions so all sides of the fiber see the "Mighty Kirby Brush" . | ||||||
 | 24. It looks clean but yous not quite washed withal. Allow it dry out completely (commonly takes 1-iii hours, if you did 2-iii passes with Kirby shampooer it may accept a fleck longer). There is withal some dirt left that brush did not scoop upwardly simply when drying shampoo does not let the dirt stick back to the rug. Later it dries some dirt is nevertheless in that location but it is dry and loose and can be picked up vacuuming. Accept a few more minutes and thoroughly vacuum the dry out carpet. | ||||||
| Cleaning the Kirby shampooer Take everything autonomously. Rinse all parts EXCEPT the brush roll! Just let the brush dry out. When putting Kirby shampoo accessory away for storage - do not twist the knob all the way (if you store the nozzle and tray assembled). Rubber will stretch and you volition need a new chugalug. Simply turn the Kirby shampooer knob but enough for the hook to grab onto the chugalug but do not stretch information technology at all. | |||||||
| This is all that is to our Kirby shampooer manual . In that location are many tips and tricks using Kirby shampoo just this should exist enough (if non more than y'all need) to get you started. Accept a clean house :-) | |||||||
Source: https://www.goodvac.com/Articles.asp?ID=153
0 Response to "How To Set Up Kirby Carpet Shampooer"
Post a Comment